Suzuki Grand Vitara SQ416/SQ420/420WD

since 1998 of release

Repair and car operation



Suzuki Grandee of Wetar
+ General information
- Maintenance and greasing
   + Service
   - Maintenance
      - Engine
         Driving belt
         GRM belt (only for G16 engines)
         Klapanny gap (only for G16 engines)
         Engine oil and filter
         Cooling liquid
         Exhaust system
      + ignition System
      + Fuel system
      + System of decrease in toxicity of an exhaust
      + Chassis and body
      Final survey
   Recommended liquids and lubricants
+ Heater, ventilation and conditioner
+ Steering
+ Suspension bracket
+ Wheels and tires
+ Forward driving shaft/bearing of a shaft. Oil epiploon
+ Driveshafts
+ Brake system
+ Engines
+ Fuel system
+ ignition System
+ start System
+ release System
+ Transmissions
+ Coupling
+ Transfer
+ Forward and back differentials
+ Windows, mirrors, locks and security measures. Immobilizer
+ Electric equipment


5917e1e5



Maintenance

Engine

Driving belt

Any check and replacement of spare parts are carried out only on the idle engine.

Check of a belt of the generator and the cooling pump (on G16 engines)

 PERFORMANCE ORDER

  1. Disconnect "weight" from joint stock bank.
  2. Believe a belt on cracks, anguishes, deformation, wear and purity.
  3. At detection of any defect replace a belt.
  4. Check a belt on a tension.
    • Tension of a belt of the generator and cooling pomp:
      • "and" — a deflection of 5 — 7 mm (0.20 — 0.28 inches) for G16.

1 — a pulley of a cranked shaft
2 — a pulley of the water pump
3 — 100 N, 10 kg or 22 pounds


At replacement of a belt on new, adjust a belt tension to a deflection of 5 — 6 mm (0. 20 — 0. 24 inches) for G16.

  1. If a belt will draw or it is too poorly tense, adjust to norm, by generator moving.
  2. Tighten an adjusting bolt of the generator and шкворень.
  3. Connect "weight" to joint stock bank.

Replacement of a belt of the generator and cooling pomp (on G16 engines)

Replace a belt. See. A belt of the cooling fan in Head engine Cooling for procedure of replacement of a belt of the water pump.

Check of a driving belt of the pump of cooling, the generator, the amplifier of a wheel, the conditioner compressor (if it is provided)

type and — dark green labels on a natyazhitel
type b — yellow labels on a natyazhitel
“A” — the indicator
“a” — area of a normal tension
“b” — limiting area
“c” — area of excess of a limit.


 PERFORMANCE ORDER

  1. Disconnect "weight" from joint stock bank.
  2. Check a belt on cracks, anguishes, deformation, wear and purity.
  3. At detection of any defect replace a belt
  4. Check, that the indicator of a natyazhitel of "A" was in the area "a".
  5. If the indicator "A" is in the zone "c", having passed «b», replace a generator belt with the new.

Use a mirror at check of a tension of a belt of a natyazhitel of the type "A".

Replacement of a driving belt of the pump of cooling, the generator, the amplifier of a wheel, the conditioner compressor (if it is provided) (on the J20 engine)

Replace a belt according to procedure of replacement of a belt of the generator in Head electric equipment System.

Check of a driving belt of the fan of cooling of the engine (for the J20 engine)

1 — 100 N, 10 kg or 22 pounds
2 — the fan coupling
3 — the crankshaft coupling
4 — an adjusting bolt and шкворень


 PERFORMANCE ORDER

  1. Disconnect "weight" from joint stock bank.
  2. Check a belt on cracks, anguishes, deformation, wear and purity.
  3. At detection of any defect replace a belt
  4. Check a belt on a tension
    • Tension of a belt of the fan of cooling:
      • «a» — a deflection in 5-7 mm (0. 20-0. The 27th inch) under load of 100 N, 10 kg or 22 pounds.

At replacement of a belt on new, adjust a belt tension to a deflection of 4 — 5 mm (0. 16 — 0. The 19th inch) for G16.

  1. If a belt will draw or it is too poorly tense, adjust to norm, by adjustment of a pulley of the fan of cooling.
  2. Tighten an adjusting bolt of the generator and шкворень.
  3. Connect "weight" to joint stock bank.

Replacement of a belt of the fan of cooling (on the J20 engine)

Replace, according to procedure of replacement of a driving belt of the fan of cooling in the Section the Belt of the cooling fan in Head engine Cooling.

Check of a driving belt of the pump of the power steering and the conditioner compressor (if it is established) (on G16 engines)

1 — a crankshaft pulley
2 — a pulley of the pump of the power steering
3 — a pulley of the compressor of the conditioner (if it is equipped)
4 — a pulley of a natyazhitel of a belt
5 — bolts of a pulley of a natyazhitel
[A]: G16 with P/S
[B]: G16 with P/S and A/C


 PERFORMANCE ORDER

  1. Disconnect "weight" from joint stock bank.
  2. Check a belt on cracks, anguishes, deformation, wear and purity.
  3. At detection of any defect replace a belt.
  4. Check a belt tension
    • Tension of a belt of the pump of the power steering and conditioner compressor:
      • «a» — a deflection in 6-9 mm (0.24 – 0.35 inches) under load of 100 N, 10 kg or 22 pounds.
      • «b» — a deflection in 4-7 mm (0.16 – 0.28 inches) under load of 100 N, 10 kg or 22 pounds.
  5. If the tension of a belt falls outside the limits this specification, adjust according to the Section the Driving belt of the pump of the power steering in Head power steering System.
  6. Connect "weight" to joint stock bank.

Replacement of a driving belt of the pump of the power steering and/or the conditioner compressor (if it is established) (on G16 engines)

Replace a belt and then adjust its tension according to the procedure of replacement of a belt described in the Section the Driving belt of the pump of the power steering in Head System of the power steering.